Faux-Fabric Paper Snowman {Tutorial}

A few weeks ago I was lucky enough to be a creative guest on Ucreate!!!!!  Yes, I know, big deal, right? Right!

I decided to stick with my M.O. and do a paper tutorial. I’m always trying to push the boundaries of paper and test its limits. I love fabric snowmen, but as you may know, I don’t sew! So the challenge became how to make a faux-fabric snowman out of paper. Ta da! I’m sharing these now because they will be cute to display all winter long.

Faux-Fabric Paper Snowman Tutorial


Supply list:

  • Heavyweight white paper* in large sheets
  • Water and spray bottle
  • Rubber bands
  • Hot glue gun
  • Packing paper or white newsprint

Optional accessories—such as:

  • Tattered Angels Glimmer Mist
  • Burlap, ribbon, or fabric
  • Buttons or brooches
  • Wood pieces
  • Embossing powder and heat gun

*I used 180 gsm handmade paper, in 22”x30” sheets, made out of cotton, silk, and agro waste (such as sugarcane waste, bark fibers, or jute waste), from Under the Sun—but any heavyweight, fibrous paper will do.


Cut a circle from the white paper approx. 20 in. diameter (for larger snowmen; 15 in. for smaller ones.)


Roll sheets of packing paper towards the center until you have a balled circle.  Secure with hot glue.

WB_128[4]---  WB_125[5]- 

Add layers until you have formed a ball, approx.  5 – 6 in. diameter (3 – 4 in. for smaller snowmen).

WB_133[5]-  WB_135[4]-  WB_139[4]-- 

Now comes the fun part! Take your white paper circle and run it under your tap. Yes, you read me correctly. Get that paper wet! Wet the top and bottom thoroughly.


This is when you need to work quickly, because as soon as your paper gets wet the clock is ticking to get it into position before it tears, pills, or just becomes unworkable. Set your packing-paper ball in the center of the wet paper and start gathering the paper up to the top. If the paper is too stiff, spray it with a spray bottle.  If you work it too much, it will look like crumpled paper, and we are going for more of a gathered fabric look, so be quick!

WB_148[6]-  WB_153[6]-  WB_156[5]-

Once you have it gathered at the top, and it looks the way you want it to, secure the top tightly with a rubber band.

WB_169[5]-  WB_171[5]-  WB_173[4]-

Now, cut another paper circle out of your heavy white paper approx. 12 in. diameter (for larger snowmen; 9 in. for smaller ones).  Cut a small circle (approx. 1 inch) out of the center of the paper.  Cut the hole to fit snuggly over the top of the gathered paper ball.  Cut it smaller at first, gradually increasing the size as needed, so as not to become too big.


Once the hole fits snuggly over the secure rubber band, push the paper down as far as it will go. Use a pair of sharp scissors to snip the rubber band without cutting the paper. Remove the rubber band carefully. This should cause the wet paper to expand and hold the new circle in place.

WB_175[6]--  WB_177[5]- 

Roll and twist another piece of newsprint or packing paper, and wind it around the paper sticking out of the hole.  Secure it with hot glue. Try to shape an even form ball of about 2.5 – 3 in. diameter.

WB_182[4]---  WB_186[4]-  WB_190[4]-

Using your spray bottle, wet the white paper circle that is now secured underneath the ball.  Wet both sides, and start gathering it at the top the way you did the bottom ball. Again, remember to work quickly. When completely gathered on the top, secure it with a rubber band.

WB_193[4]-  WB_197[4]-  WB_198[4]--


This is the basic snowman—now use your imagination to make it your own! I sprayed mine at this point with marshmallow glimmer mist so it would have a shimmered frosty look.

WB_213[6]-  WB_216[5]-

I made a top hat for the dad, a wide-brim church hat for the mom, and a cute beret-like snow-hat for the daughter.

Top Hat 2 Church Hat Beret

For the daughter’s beret, I made it much the same way I did the head. I cut a circle out of paper approx. 4.5 in., and cut a hole in the middle to fit over the gathered paper. after removing the rubber band, I wet the paper and gathered and twisted it in the center while laying it flat like a beret. I added a wool ball to the top that Heather made using Whitney’s tutorial.  For the top hat and wide brim hat, I cut a circle the size I wanted for the brim, and then cut the hole in the center. After making sure the fit was right, I sprayed the brim with silver sugar glimmer mist, and then coated it with embossing powder and set it with my heat tool. I then put it in place atop the head, and cut the rubber band. I then built the rest of the hat right on the head.

WB_219[5]-  WB_221[4]-

Embellish your snowmen with accessories of your choice. I used burlap, fibers, and buttons (as well as a cute little scarf crocheted out of yarn by Heather).

WB_229[10]-  WB_231[10]-  WB_235[16]

WB_239[6]  WB_242[4]

For the dad’s sign, I used Woodsies from Michael’s—and I sanded and inked the edges. I printed the words on my computer, and tore the edges before gluing it onto the sign.


I dabbed Snow-Tex on the top of the sign, and on the hats, to look like melting snow. I rolled paper for their noses, and used little black embellishments for their coal eyes. Have fun, and decorate them to match your style and décor!


Display these all winter long. I’m not taking my little family down until Valentine’s Day!




  1. Carrie @ Cottage Cozy says

    What a darling snowman!

    Merry Merry Christmas! May your stocking be filled with blessings!

    Hugs, Carrie

  2. Haley K says

    Oh I love all of their unique hats! :) And that saying, "Families are forever because love never melts" is just too perfect :)

  3. [email protected] says

    Aww, those are way cute! And I love that they're paper! Thanks so much for the how-to, I'll be linking.

  4. Mrs Frizz says

    oh wow … this wee family is absolutely g.o.r.g.e.o.u.s.

    I collect Snowmen and Santa's … might have to remember these for next year.

    Thank you for sharing.

  5. says

    Thank you for this article. That’s all I can say. You most definitely have made this blog into something special. You clearly know what you are doing, you’ve covered so many bases.Thanks!


Leave a Reply

Your email address will not be published. Required fields are marked *

You may use these HTML tags and attributes: <a href="" title=""> <abbr title=""> <acronym title=""> <b> <blockquote cite=""> <cite> <code> <del datetime=""> <em> <i> <q cite=""> <strike> <strong>